End Stage assembling computers

Replace the chassis cover by sliding
connect the cable from the power supply into the wall socket.
Connect the monitor to the video card port.
Connect the phone cable into the modem port if any.
Connect the keyboard cable connector and plug the mouse into the mouse port or serial poert (depending on the type of mouse).
Connect other external devices such as speakers, joystick, and microphone if there is to the appropriate port. Check the manual of the adapter cards to ensure the port location.
Testing
The new computer is assembled can be tested by running the BIOS setup program. How to do a test with the BIOS program as follows:
Turn on the monitor and system unit. Note the display monitor and the sound from the speakers.
Fost of the BIOS program will automatically detect the installed computer hardware. If there are errors then display a blank screen and the speaker sounds a beep on a regular basis as an indication of error codes. Check reference BIOS code to find an error indication is meant by the beep code.
If no error occurs then the monitor displays the execution of the POST program. BIOS interrupt key ekan according to the instructions on the screen to enter the BIOS setup program.
Check all the hardware detection by the BIOS setup program. Some settings may have changed in value, especially the capacity of hard drives and boot sequence.
Save changes to the settings and exit the BIOS setup.
After exit from the BIOS setup, the computer will load the Operating System with appropriate search order settings in the BIOS boot sequence. Insert Bootable Diskette or CD containing the operating system to drive the search.
Handling Problems
A common problem in computer assembly and handling, among others:
Computer or monitor is not lit, probably due to the switch or power cord not connected.
Card adapter is not detected due to the installation of not fitting into the card slot /
LED of the hard disk, floppy or CD burning continue due to wiring error or a pin connector that fits yet connected. Congratulations and Good Trying Helpful.

Read more »

Install Card Adapter

A common adapter card is installed video cards, sound, network, modem and SCSI adapters. Video card should generally be installed and installed before any other adapter card. How to install the adapter: Hold the edge of the adapter card, avoid touching the electronic components or circuits. Press the card to plug right into the expansion slot on the motherboard
Place the retaining screw to the chassis card
Reconnect the internal cable to the card, if any.

Read more »

Install Drive

The procedure to install the hard disk drive, floppy, CD ROM, CD-RW or DVD is the same as follows:
Pellet dislodged drive bay cover (space to drive on the casing)
Enter from the front drive bays with the first set the jumper settings (as master or slave) on the drive.
Adjust the position of screw holes in the drive and chassis retaining screws, then install the drive.
Connect the IDE cable connector to the drive and the connector on the motherboard (the connector is used first primary)
1 samapai Repeat step 4 for each installation drive.
If the IDE cable connected to the du drive jumper settings make sure that the difference of the two first drive set as master and the other as slave.
Secondary IDE connector on the motherboard can be used to connect two additional drives.
Floppy drive is connected to a special connector on the motherboard floppy
Connect the power cable from the power supply to each drive.

Read more »

Install the motherboard and chassis cable

After the motherboard installed in the chassis next step is to install the cable I / O on the motherboard and the casing panels.
Connect the data cable for the floppy drive controller on a floppy connector on the motherboard
Connect the IDE cable connector to the primary and secondary IDE on the motherboard.
For non-ATX motherboard. Connect the serial cable and parallel port on the connector on the motherboard. Note the position of pin 1 to install.
On the back of the casing there is a hole to install an additional port types of non-slot. Open the lock plate screw holes covered lalumasukkan port to port connectors installed and put screws back.
When the mouse port not available at the back of the card casing mouse connectors must be installed and connected to the mouse connector on the motherboard.
Relations switch cable connector from the chassis front panel, LED, internal speakers and ports that were installed in front of the casing when the motherboard. Check your motherboard diagram to locate the right connectors

Read more »